Loaded Pickguard - For Telecaster® Custom®

We are pleased to offer this assembled wiring loom, fitted directly to a plate, suitable for an Fender® Custom® .

Built in-house using high quality parts, the classic black pickguard comes fitted four 500k short, split shaft CTS pots, two 0.022 orange drop capacitor, A switchcraft toggle switch* and mono socket, and its all wired up wiring metal braided, wax cloth hookup wire.

Loaded Pickguard - For Telecaster® Deluxe® (2004 - Present)

We are pleased to offer this assembled wiring loom, fitted directly to a plate, suitable for an Fender® Deluxe® .

Built in-house using high quality parts, the classic black pickguard comes fitted four 500k short, split shaft CTS pots, two 0.022 orange drop capacitor, A switchcraft toggle switch* and mono socket, and its all wired up wiring metal braided, wax cloth hookup wire.

Wiring Loom - For Telecaster® Deluxe & Custom

Suitable for Telecaster® Deluxe & Custom style guitars, with the 4 controls and 3 way toggle switch on the upper bout.

Please note, these are not official Fender® parts.

Wiring Loom - For Gibson® SG®

Suitable for a SG®

Please note, these are not official Epiphone® or Gibson® parts.

Wiring Loom - For Hollow Bodies

Suitable for a Casino®, 335® and similar

Please note, these are not official Epiphone® or Gibson® parts.

Wiring Loom - For Les Paul®

Suitable for a Epiphone® Les Paul® and similar

Please note, these are not official Epiphone® or Gibson® parts.

Control Loom - For Stratocaster® - SCSCSC (5 Way) - Solderless Connection

A solderless version of our standard 5 way loom - built around screw terminals, so no need to solder a single connection on this assembly. Couldn't be easier to install.

Please note, these are not official Fender® parts.

Standard Control Loom w/ Pickguard & Knobs

This is a "loaded plate" - a pickguard, for the Fender® Stratocaster, with the volume pot, tone pots, and switch all installed and wired up, ready to have pickups connected.

You're getting everything you need to build the plate up - the knobs and switch top are on there, the pickup covers are in there in the same colour as the knobs, and you're getting the pickup height bolts too.

Please note, these are not official Fender® parts.

Loaded Pickguard - For Telecaster® Thinline

We are pleased to offer this pre-assembled wiring loom, fitted directly to a plate, suitable for an Fender® Telecaster® Thinline.

Built in-house using high quality parts, the classic white pickguard comes fitted two 250k short shaft pots, one orange drop capacitor and one three way switch, and is finished with two flat top knobs and a black top hat switch tip.

Wiring Loom - For Gibson® Flying V® (1958)

Suitable for a 1958 Flying V® and similar

Please note, these are not official Epiphone® or Gibson® parts.

Wiring Loom - For Gibson® Flying V® (1963)

Suitable for a Flying V® and similar

Please note, these are not official Epiphone® or Gibson® parts.

Control Loom - For Stratocaster® - SCSCSC (6 Way)

With Oak Grigsby releasing the new 6 way switch for the Strat, is only seems right that we put out a complete wiring loom including it too. Allowing you to have the usual 5 positions, plus bridge and neck in parallel, it really is a versatile part that brings something new to your setup.

Please note, these are not official Fender® parts.

Control Loom - For Stratocaster® - HBSCSC (5 Way w/ Auto Coil Split)

This is a loom designed for a Stratocaster® with a humbucker in the bridge position, and single coils in neck and bridge.

Please note, these are not official Fender® parts.

Control Loom - For Stratocaster® - SCSCSC (5 Way w/ Neck Blend)

A Stratocaster wiring loom, all hooked up and ready to connect pickup to, hand made here in the UK.
Functioning slightly different to the standard setup, you've got a master volume, master tone, and a blend pot which allows you to add in the neck pickup when the bridge pickup is also on.

Please note, these are not official Fender® parts.

Control Loom - For Stratocaster® - SCSCSC (3 Way)

A wiring loom done to vintage specifications - almost identical to the modern style, but with only 3 way switching, and a larger value cap (in this case, 0.1) - beyond that its business as usual - all dont with the highest quality parts, to the highest possible standard right here in the UK

Please note, these are not official Fender® parts.

Control Loom - For Stratocaster® - SCSCSC (5 Way)

A wiring loom for a Stratocaster® or similar guitar, wired exactly as you expect - 5 way switching, 1 volume, 2 tone - all dont with the highest quality parts, to the highest possible standard right here in the UK

Please note, these are not official Fender® parts.

Wiring loom w/ Varitone

Suitable for a Epiphone Lucile®, 345® and similar

Please note, these are not official Epiphone® or Gibson® parts.

Control Assembly - For Esquire®

A completely constructed Control plate, for a Fender® Esquire®, the single pickup compatriot to the very first Telecaster® guitars - the control setup on the Esquire®, if you've never played one, is most likely, a complete mystery to most people - so before we get into the parts used here on this assembly, its probably worth covering what the Esquire® does (for better or worse)

Please note, these are not official Fender® parts.

"Thick Top" Arch Top Wiring Kit- High End

A complete wiring solution for most Gibson* Les Pauls, featuring long shaft CTS pots, a Switchcraft 3 way toggle switch and orange drop caps. This really is a top end wiring loom.

Now available with braided metal hookup wire with wax coated inner core and a switchcraft mono socket.

Please Note - Now available with " Extender Switch Nut" for guitars with a top panel thicker then 4mm.

Wiring Kit - HBHB - 3 Control

This is a Wiring kit designed for as an upgrade, primarily, for PRS® SE (and other models produced in the far east) with 2 Volume and 1 Tone controls, and a 3 way toggle switch.

Control Assembly - For Tele® - 4 way Mod

A completely constructed Control plate, for a Fender® Telecaster®, wired to the the 4 way mod version - Standard switching plus an extra option for both pickups in series, 1 volume, 1 tone, bridge, both and neck - a Tele® with a little bit more on offer.

Built using the highest spec parts - CTS pots, Oak Grigsby Switch, Cornell dubillier cap, 22 AWG vintage cloth hookup wire and a switchcraft socket, all connected together, ready to do, and mounted onto a beautifully plated control plate and barell knobs fitted.

Please note, these are not official Fender® parts.

Control Assembly - For Nashville Tele®

A completely constructed Control plate, for a Fender® Nashville Telecaster®, differing from a Normal Tele® in that is has 3 pickups, rather then 2, so this is reflected in the switch so you're getting the following setup- 5 way switching, 1 volume, 1 tone, bridge, both and neck.

Built using the highest spec parts - CTS pots, Oak Grigsby Switch, Cornell Dubillier cap, 22 AWG vintage cloth hookup wire and a Switchcraft socket, all connected together, ready to do, and mounted onto a beautifully plated control plate and barrell knobs fitted.

Please note, these are not official Fender® parts.

Control Assembly - For Tele®

A completely constructed Control plate, for a Fender® Telecaster®, wired to the modern standard - 3 way switching, 1 volume, 1 tone, bridge, both and neck - as we all know and love.

Built using the highest spec parts - CTS pots, Oak Grigsby Switch, Cornell Dubillier cap, 22 AWG vintage cloth hookup wire and a Switchcraft socket, all connected together, ready to do, and mounted onto a beautifully plated control plate and barrell knobs fitted.

Please note, these are not official Fender® parts.

Control Assembly - Suitable for Fender® Jaguar® Guitar

A control assembly for the Fender® Jaguar guitar - loaded up with CTS pots, and a switchcraft mono socket.

Please note, these are not official Fender® parts.

SE3P-A - 3 band EQ system

A good example of a compact 3 band EQ system, using a B500k concentric pots with central indents to control bass and treble on the 1st pot and middle and frequency on the second. A regular A500k for volume and an MN500k blend pot for pickup selection.

Control Assembly - For Tele® Thinline

Exactly the same as a normal Telecaster control loom, but the pots on the thinline are a little closer together, and, obviously, you dont have the control plate thanks to that iconic pickguard - beyond that - identical! All hand made in the UK using high quality parts, ready to drop into your guitar.

Built using the highest spec parts - CTS pots, Oak Grigsby Switch, Cornell Dubillier cap, 22 AWG vintage cloth hookup wire and a Switchcraft socket, all connected together, ready to do, and mounted onto a beautifully plated control plate and barrell knobs fitted.

Please note, these are not official Fender® parts.

Control Assembly - Suitable for Fender® Mustang® Guitar

A control assembly for the Fender® Mustang guitar - loaded up with CTS pots, and a switchcraft mono socket.

Please note, these are not official Fender® parts.

Control Assembly - Suitable for Fender® Mustang® Bass

A control assembly for the Fender® Mustang bass - specifically those models with only 1 pickup, similar to the Precision® bass.

Please note, these are not official Fender® parts.

Control Assembly - Suitable for Fender® Jazz® Bass

Suitable for a Jazz® Bass

Please note, these are not official Fender® parts.

"Volume only" Control Assembly - For Esquire®

A bit of a strange plate all things considered - designed to fit onto a Fender® Esquire® (or any other Telecaster® with only one pickup) - but cutting away all the bells and whistles - no 3 way switch, no tone control - just a volume control, and a mono socket on the output.

A great way to turn your Esquire into a no-nonsense player!