Home > Pickguards, Knobs & Covers > Knobs, Covers & Tips > For Telecaster®
Sort By:
Page of 1
Fender® Telecaster® Bridge Cover Bridge Cover - For Vintage Telecaster®

Designed for a Vintage Telecaster® Bridge and a great part to put that finishing touch on your Tele®. First introduced in the early 50's , where most ended up as portable ashtrays for the gigging musician, the early models had a distinctive solder drop or solder mark on the inner face due the fact that a wire was attached during the electro-plating process. The later models have no such mark because the plating process moved onto specially designed racks.

Please note, these are not official Fender® parts.

Prices From: £23.47 Inc VAT
Black Witch Hat Knobs for Solid Shaft Pots 4 x Witchhat knobs for Solid Shaft (w/ Set Screw)

Available in Black Silver Inlays, and suitable for the Telecaster Deluxe and Custom

Supplied singly (Vol or Tone) or in a set of 4 (2 Vol and 2 Tone)

Prices From: £16.32 Inc VAT
An Axesrus Vintage Neck Pickup Cover "Tall & Open" Lipstick Pickup Cover For Fender® Telecaster®

With tall covers and tall poles, comes increased space internally for copper - allowing you to wind a pickup to a respectable level with 42 AWG, or to use 1/4" poles with 43 AWG, or, just to go completely off the rails and design something completely unique!

Please note, these are not official Fender® parts.

Prices From: £15.47 Inc VAT
An Axesrus Vintage Neck Pickup Cover "Tall & Vintage" Lipstick Pickup Cover For Fender® Telecaster®

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars

Please note, these are not official Fender® parts.

Prices From: £15.47 Inc VAT
A Control Plate with Toggle Switch Hole for Fender® Telecaster® Control Plate With Toggle Switch Hole - Suitable For Telecaster® - 32mm Wide

A 32mm wide control plate for the Telecaster®, with a hole for a toggle switch. Fantastically well finished, with a high level of electroplating. Supplied with cross head, recessed mounting screws. Please note these are not official Fender® parts.

Prices From: £11.16 Inc VAT
A Selection of Control Plates with Slanted Switch Slot for Fender® Telecaster® Control Plate With Slanted Switch Slot - Suitable For Telecaster® - 32mm Wide

A 32mm wide control plate for the Telecaster® with a slanted switch slot. Fantastically well finished, with a high level of electroplating. Supplied with cross head, recessed mounting screws. Please note these are not official Fender® parts.

Prices From: £11.16 Inc VAT
A Selection of Axesrus Blank Steel Control Plates for Fender® Telecaster® Blank Control Plate - Suitable For Telecaster® - 32mm Wide

A blank control plate for the Telecaster®, fantastically well finished, with a high level of electroplating.




Prices From: £11.16 Inc VAT
Pickup Covers for DiMarzio pickups for Telecaster Necks Lipstick Pickup Cover - for DiMarzio® Pickups for Telecaster® Necks

These are the style of covers that DiMarzio® fit to their pickups designed to go into Telecaster® neck slots - slightly different to a "normal" covers because they incorporate that "triangular" shape, and flat top from a vintage cover (although the "shape" is much less angular) but the cover is more "complete", like a modern version (where the coils are completely surrounded by the cover)

Please note, these are not official DiMarzio® parts.

Prices From: £8.32 Inc VAT
Selection of Axesrus Steel Control Plates for Fender® Telecaster® Control Plate - Suitable For Telecaster® - 32.2mm Wide

A standard control plate for the Telecaster®, in the size most commonly used by Fender® Japan - slightly wider then the USA version, and drilled out to accept metric sized pots.

Prices From: £6.91 Inc VAT

(1)
Selection of Axesrus Steel Control Plates for Fender® Telecaster® Control Plate - Suitable For Telecaster® - 32mm Wide

A standard control plate for the Telecaster®, with a standard switch slot, and two pot holes large enough to take CTS pots. Fantastically well finished, with a high level of electroplating.

Prices From: £6.91 Inc VAT

(1)
Hot Dog Control Plate - 33.5mm Wide Control Plate - Suitable For Telecaster® - 34mm Wide

A standard "Hot Dog" control plate drilled for Volume and Tone pots, and a standard switch. Plated to the highest standard with a conductive material to minimise the amount of ground wires you’ll need.


Prices From: £6.91 Inc VAT
An Axesrus Neck Pickup Cover for the Fender Telecaster Lipstick Pickup Cover for Fender® Telecaster®

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars. These covers have a curved top.

Please note, these are not official Fender® parts.

Prices From: £5.47 Inc VAT
An Axesrus Vintage Neck Pickup Cover "Vintage" Lipstick Pickup Cover For Fender® Telecaster®

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars

Please note, these are not official Fender® parts.

Prices From: £5.47 Inc VAT
A Selection of Open Top Lipstick Pickup Covers Open Top Lipstick Pickup Cover For Fender® Telecaster®

Open Top Lipstick pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars.

Please note, these are not official Fender® parts.

Prices From: £5.47 Inc VAT
A Flat Topped Axesrus Neck Pickup Cover Lipstick Pickup Cover For Fender® Telecaster®- Brass

Standard Lipstick neck pickup covers as seen on Telecaster® guitars. A great way to breathe a bit of life into your old guitars. These covers have a flat top.

Please note, these are not official Fender® parts.

Prices From: £5.47 Inc VAT
Chrome, Gold or Black Lipstick Pickup Surrounds Pickup Surround - for Fender® Telecaster® Neck

A great alternative to a pickguard, designed to mount a Telecaster® Neck Lipstick Pickup

Prices From: £5.20 Inc VAT
1 x Barrel Style Knob - Split Shaft Push On 5.9mm 1 x Barrel Style Knob - Push On

Available in Gold, Black and Chrome Dome topped,and Chrome Flat top. Suitable for Alpha Split Shaft Pots with a 5.9mm post. Mounted with internal push on bush.

Prices From: £3.58 Inc VAT
Barrel Knobs - Domed w/ Position Marker Barrel Knobs - Domed w/ Position Marker

Suitable for Alpha and CTS pots, in both Split shaft or Solid Shaft versions.

Mounted with a slot head grub screw.

Prices From: £3.48 Inc VAT
Barrel Knob - Flat 1 x Barrel Knob - Flat

Suitable for Alpha and CTS pots, in both Split shaft or Solid Shaft versions.

Mounted with a slot head grub screw.

Prices From: £3.48 Inc VAT
Domed Barrel Knobs Barrel Knobs - Domed

Suitable for Alpha and CTS pots, in both Split shaft or Solid Shaft versions.

Mounted with a slot head grub screw.

Prices From: £3.48 Inc VAT

(1)
A Selection of Switch tips to fit Oak Grigsby, CRL, Fender and Axesrus switches 1 x Switch Tips (Push Fit)

Available in  "Tear Drop", "Barrel" and "Top Hat" styles - in both 5mm, 4mm and 3.5mm sizes.

Prices From: £2.20 Inc VAT
2 x Import Sized Push Fit Barrel / Top HatSwitch Tips 1 x Import Sized Push Fit Barrel / Top Hat Switch Tips

Made for Shallow body switches.

Prices From: £1.80 Inc VAT