|
|
|
|
Main Description
The Power to Perform
The Ethereal is a bit of a strange pickup on the face of it - it’s so highly wound at 17K that you’re instantly thinking “this is going to be high output/tons of gain/wont clean up” but its actually a bit “Sheep in Wolves clothing” – and as such, performs much more like what we’d associate with a medium output humbucker.
That’s not to say the Ethereal won’t hold its own when it comes to rock and metal – but in real terms, where something like the Hot Iron will give you a blistering lower mid-range punch in the gut, or the Wraith will tear your face off at 100 paces with its trashy, razor sharp attack, the Ethereal a little more refined, more the virtuosos pickup then the metal heads.
Rather than aiming to give you bucket loads of heat and definition and really play up to that "metal monster" ethos we all have for high output pickups, its actually designed to give you a real warmth, with plenty of responsiveness that makes them perfect for hammer ones, arpeggios, intricate picking.
Sure it'll distort with the best of them, and that power can quickly be harnessed when you need it, but this is more the "every day" high output side of things - when you need a pickup that’s going to really give you plenty of body, plenty of warmth, not a huge amount of top end and will actually behave itself when you're not in full blown Rock God mode.
Gibson®, Epiphone®, Stratocaster® and Strat® are registered trademarks of Fender Musical Instruments Corporation and Gibson Musical Instruments Corporation. Axesrus® has no affiliation with FMIC
Sound Clips
Should be just below!
Videos
The Good & The Bad
Between you, me and the fence post, I'm more an engineer then i am a salesman, so to scratch that itch - I’m compelled to not only write up the unavoidable "hey, this pickup great! Play Rock or Blues?! This one’s for you!", but for the sake of balance, it’s only fair that i get to write up what they're not great at too (and because this section isn't "up front" - i get to be a bit more technical about it too! Who knows, maybe I’ll be able to explain what all those lovely buzz words actually mean eh?)
Remember too - whilst I’m writing this stuff about Axesrus pickups, its true of every pickup ever made. Even if you’re not buying ours, this stuff is handy! It’s all true! all pickups have characteristics that make them good or bad... there are no perfect pickups!
Medium Output?!
Now, I've got a bit of a chip on my shoulder of the term "medium output" - mainly because it’s a term that sounds so underwhelming, that it’s difficult, if not impossible, to get excited about, but, honestly? It’s a pretty fitting description of what this style of pickup is doing.
If we think about humbuckers in 3 main "styles" - where there’s "Vintage" (Low output... an equally catchy name!), “Medium output” (I should have really pushed for something like “modern output” in retrospect) and “high output” (annoyingly accurate, because its true, high output pickups, are, always, producing higher output – no trick there!)
As a general rule – vintage humbuckers are always wound with 42 AWG, and are the brightest/lightest in the bass, high outputs (and it’s a fairly wide ranging collection) are wound with 43 (or 44 AWG would to a very high resistance!), will occasionally use larger poles in an effort to increase their inductance, and they’re the darkest, dirtiest, beefiest offerings.
And then “medium output” – kind of sits in the middle of that.
However – how it gets there, isn’t quite as clear cut as you’d expect. It’s (just) possible (if not exactly sensible) to hugely overwind a vintage humbucker (retaining that 42 AWG) to, say, 10K, which will push that idea into “medium output” as the resonant peak is pushed down into a lower register, the bass increases, and the pickup becomes considerably darker, but also, more capable of being pushed harder under gain – OR – you can under wind a high output pickup – which is actually the more common way of doing it.
So, our Model 24, usings 43 AWG, wound to just over 11K, and the Ethereal looks a monster at 17K using 44 AWG, but, really? Its not! Maybe its better to think of this style of pickup not as medium outputs, but as “underwound high outputs”? Who knows?!
Either way, the one thing that they do give you, is a huge amount of versatility – they’re capable of being kept “cleaner” than a true high output, but, equally, they’re capable of being pushed much further into distortion then a vintage pickup.
Without wanting to sound the salesman in this, I always think, when people go in for “medium” pickups – “There goes a player who’s working for a living” – the “warts and all” vintage stuff is great if you want to meet your hero’s, and the high gain, high output, high octane stuff, kind of has a “folly of youth” thing about it – and they’re great! Honestly! But one day, you’ll find something they just can’t do. Medium humbuckers don’t suffer that problem. They’ll do everything you throw at them, and keep going. And as much as that may seem like an absolutely awful selling point, and I’m pitching them as a “Jack of all trades” pickup… lets be honest! That’s not the worst thing in the world if its going to save you taking 5 very specialist guitars out on the road.
So, yeah, “medium output”? Terrible name, absolutely inspiring frankly, and probably not the best tone you’ll ever hear, but they cover so much ground, and they’ll do it all pretty well, that having a set of them in the locker, isn’t a bad place to be what so ever.
Bode Plots
|
Swap Graphs?
|
Pickup #1
|
Pickup #2
|
Setup
500k pots work perfectly (thats what was used on the recordings for reference) and a 0.022 or a 0.047 cap on the tone will see you absolutely fine - you can try a 300k tone pot if you like, but i've never felt it made much of a difference myself.
Covers, as always, mute what top end "snap" there is ever so slightly - i actually prefer the Ethereal without a cover, because, as often with higher output humbuckers, were looking to retain some more of the definition, especially considering that the resonant peak has been pushed considerablly further down into the lower frequencies.
Warranty & Returns
In an ideal world, I wouldn’t have to write this section up, and, I really wish I didn’t have to, but, if I’m being honest and transparent about how pickups work, for better or worse, it’s probably worth being honest and open your rights as a consumer too, and maybe give a little insight into how we actually build pickups.
How we do it
Pickups, at our end of things – are “Custom made” – I cannot stress this enough. When you click the “Add To Cart” button, there is no pickup on the shelf, no bucket of pre-terminated bobbins or half complete pickups. It is made, entirely, from scratch using the parts we have available.
This means, if you order a Bourbon city, or a Hot Iron, or a Texas Blue, it is wound FOR YOU. It is being built to the specifications you have stipulated in the drop-down menus, even the most “normal” design, is still, essentially, built to order.
That entails our pickers collecting the parts from stores, delivering them to the winders, who then get the copper on there, and then the wound coils going to the techs to solder, terminate, test, polish, wax pot, clean, retest… you get the idea.
This is all done “in house” and, obviously, there is a queue, which is first in first out, so pickups will NEVER be shipped same day. Realistically, it takes about 2 weeks, but we do get busier at the beginning/end and middle of the month, so that can have a knock on effect.
And this is all being done, by hand, on a VERY small scale. At maximum, we can produce about 6 pickups a day.
It works wonderfully frankly, because we can make, pretty much, anything you can dream up, and keeping it small scale, means we have an exceptionally high attention to detail with each pickup sold.
Returns
So we have an item, when all is said and done, that didn’t exist until you purchased it, that has cost a lot of man hours to actually manufacture, and has been manufactured to your exact specifications.
As such, pickups come under the remit of “custom work” as laid out under the our terms and conditions, and as outlined in the UK governments distance selling regulations.
This means, in short, pickups are none returnable, and none refundable.
I understand, in this day and age, that may seem quite the hard-nosed approach, but, sadly, there’s no wiggle room in this. Once a pickup is wound, there’s no going back. It belongs to you. There is no “I’ll test it to see if I like it” or “I’ll return it if I don’t like the colour!”.
Warranty
All Axesrus pickups come with a “relaxed lifetime” warranty as far as I’m concerned. I’m never going to ask you to register the purchase, stop offering support 12 months after purchase or limit support to the initial customer in the case of second-hand stuff. We are incredibly proud of the pickups we produce, and I’ll help out wherever I can.
However, its worth laying out what I’d consider “realistic” expectations as to what we will cover as part of a warranty.
Repairs and replacements
Whilst we will not accept pickups as return for refund under any circumstances, we reserve the right to repair or replace any pickup that develops a manufacturing fault within a reasonable time frame.
I won’t put a scale on that time frame, but I will say, its at our discretion. If you’re lucky enough to have some of the VERY early hand wound stuff we made, and we (stupidly) thought we could do it at £20 a pickup, and the coil wires snapped after 10 years? I’m probably not in a position to repair or replace it free of charge, you know? You’ve had your fun; you’ve got your money’s worth!
On the flip side of that – if you’ve bought a £200 humbucker 2 years ago, and it’s developed a fault? You’d better believe Axes is bending over backwards to get it repaired and get you up and running again.
I’ll say this too, we won’t hang you out to dry – if that £20 pickup can be repaired, even if we’re not doing it as part of the warranty, we will offer to repair it at a reasonable price.
Damage vs. Fault
Pickups are delicate creatures I’m afraid. Nature of the beast I suppose, they were never designed, all those years ago, to be “presented” outside of a guitar, so go in knowing this, pickups can be damaged. Either in transit, whilst in storage, or during install.
It is VERY difficult to know how a pickup has developed a fault, so most of the time, we will go into all warranty claims with the mindset that “it’s a manufacturing fault”, frankly, because it keeps everyone happy, avoids any awkward conversations as to “who’s done what” and, normally, repairing damage done during install is the same work as repairing a manufacturing fault either way. Worst case, we might have a delicate email exchange about who’s covering the postage, but that’s about as bad as it gets.
However, we will take this approach only when a pickup, which is showing damage, is only showing minimal damage. I appreciate everyone makes mistakes.
Pickups that have been heavily damaged, have seen heavy wear and tear, or have been intentionally broken in an effort to raise a warranty claim, will see not be repaired, or replaced. Neither free of charge or “for a fee”
Lead times and cancellations
We do publish the lead times on all of our custom build work, and there is very little we can do to decrease the time it takes to actually manufacture this stuff I’m afraid, short of jumping you to the front of the queue (which is never fair, and we won’t do it)
Be aware that once an order is placed, work beings on your build, and as such, you’ve entered into the contract, and there is no backing out. Coils can often be wound within the hour or the order being placed, but they will sit in the work queue due to a back log at terminating/testing/cleaning.
Modifications
There are, occasionally, situations where someone buys a pickup, installs it, plays it for a while, and then might want something a little different down the line. Maybe a different magnet, or a cover fitting, or a new hookup wire fitting.
I am happy to carry out this work, and, normally, regardless of the “time since purchase”, this will be done simply for the cost of parts and postage.
However, the “depth” of these modifications, and if we’re willing/capable of carrying them out, is at the discretion of Axesrus. We’re happy to discuss this on a case-to-case basis, but go in eyes open, that its unlikely to be part of the warranty.
“Warranty with initial purchase”
I’m not a stickler when it comes to this stuff, but I will say, we do have to draw the line somewhere, so, strictly speaking, this “relaxed warranty” is, officially, limited to the original purchaser of the product.
That said, I’m not a robot, nor am I a fool. I’m aware that sometimes, a pickup is moved on relatively quickly, or is bought by a 3rd party for someone else, so, in these cases, lets just be sensible about it. I’ll carry forward a “true” warranty on a pickup for 12 months after the initial purchase, regardless of who is contacting me in regards to any issue.
However, I will need to know who the initial customer was. Even if it’s just their name and a rough date of purchase.
This goes for technical support too – I’ve no problems offering support on Axesrus products, regardless of “time since purchase”, but I will ask for some proof that they are in fact, Axesrus products.
Modifications to second hand parts, will be dealt with on a case-by-case basis too.
Changes in specification/tolerances
Over the years, we’ve had a few “interesting” conversations regarding pickup specifications, especially when it comes to returns and warranty.
The published specs of our pickups, are published with a “within tolerance” subtext, based off of the readings from our testing equipment.
There will, always, be variation between one pickup and the next, and whilst we endeavor to keep those readings within the tolerances stated, they do occasionally wander outside of the 10% we stipulate as “acceptable” – this is usually due to temperature fluctuation, or specification changes outside of our control (wire diameter, alloy composition etc.) – any resulting change in readings based on these factors, will result in an updated technical spec on the website, but, as you can imagine, the first we know about an unforeseen spec change, is when the pickups come off the winder.
We do not consider these “out of spec” accidents to be cause for a warranty claim I’m afraid, and we endeavor to keep on top of them so the information we’re giving you at point of purchase, is as accurate as possible.
Warranty postage
Repairs or replacement postage cost, outside of an initial 14 day period, is at your cost. I appreciate, in some situations, that this is prohibitive (especially when shipping outside of the UK).
| | |