This is a full kit to make one Rail Humbucker pickup, suitable for any single coil route, containing everything you'll need except the copper winding wire and the hookup wire.

Please note, these are not official Fender® parts.

These pickup covers are faithful reproductions of the original Single Coil covers used in the early Stratocaster® - made from Nylon rather then the PVC found on later models, and with a much softer bevel on the outside edge giving them a slightly more rounded appearance.

Nickel plated brass Eyelets, for fitting into pickup fiber board, giving you a point to thread the coil wire through, and to solder the hookup wires to.

This is a full kit to make one single coil pickup, containing the fibre board, eyelets and 1/4" Alnico poles.

This is a full kit to make one single coil pickup, containing everything you'll need except the copper winding wire.

This is a full kit to make one single coil pickup, containing everything you'll need except the copper winding wire.

This is a full kit to make one single coil pickup, containing everything you'll need except the copper winding wire.

This is a full kit for making the pickups for a Fender Mustang or similar guitar, notablly with those slightly shorter magnets, and the close faced covers.

Flat topped pole pieces, 17.5mm x 4.75mm, ideal for making replacement pickups for the Telecaster.

Available in Alnico 5.

Flat topped pole pieces, 17mm x 5mm, ideal for making replacement pickups for the Telecaster.

Available in Alnico 2, 3, 4 and 5.

These Alnico 5 pole pieces are exactly the same as we use on our single coil pickups, but we're providing them un-magnetised to allow for full customisation.

Covers for DiMarzio HS, Virtual Vintage, Injector and Area Noiseless Single Coil pickups.

Covers for DiMarzio HS, Virtual Vintage, Injector and Area Noiseless Single Coil pickups.

Covers for DiMarzio HS, Virtual Vintage, Injector and Area Noiseless Single Coil pickups.

Covers for DiMarzio HS, Virtual Vintage, Injector and Area Noiseless Single Coil pickups.

Covers for DiMarzio HS, Virtual Vintage, Injector and Area Noiseless Single Coil pickups.

Covers for DiMarzio HS, Virtual Vintage, Injector and Area Noiseless Single Coil pickups.

Covers for DiMarzio Fast Track styled pickups.

Alnico Rod magnets, suitable for Stratocaster pickups - available in alnico 5. These are a staggered set, consisting of 6 poles, with a light, vintage bevel.

Flat topped pole pieces, 12mm x 5mm, ideal for Jazzmaster® style pickups

Available in Alnico 2, 3, 4 and 5.

Alnico Rod magnets, suitable for Stratocaster pickups - available in alnico, 2, 3, 4 and 5. These are a staggered set, consisting of 6 poles, with a light, vintage bevel.

A great alternative to a pickguard for mounting single  coil pickups in a guitar with that special finish

(2)

Single coil pickup covers, suitable for most Fender pickups, as well as DiMario, Seymour Duncan and Axesrus models - spaced 52mm center to center, to take a 5mm pole diameter.

3 x 52.5mm Pickup Covers

This is a set of switch mounting and pickup height adjustment bolts for the Fender® Statocaster® and similar guitars.

Specifically, these are 6-32 UNC (imperial thread) bolts, with dome, phillips heads, with 6 "small" head screws for the pickups, and 2 larger headed versions for the switch, as well as 6 height adjustment springs.

This is a set of switch mounting and pickup height adjustment bolts for the Fender® Statocaster® and similar guitars.

Specifically, these are 6-32 UNC (imperial thread) bolts, with dome, phillips heads, with 6 "small" head screws for the pickups, and 2 larger headed versions for the switch, as well as 6 height adjustment springs.

These are the fiber boards needed to make one side loading single coil - almost identical to a standard single coil, with a base, housing 2 eyelets and the threaded height adjustment holes, and a smaller top section.

These Single coil boards, often called "flatwork" in the trade, are made to the same high standard we use on all our pickups. Constructed from Fibre board, and supplied with eyelets for easy soldering.

These Single coil boards, often called "flatwork" in the trade, are made to the same high standard we use on all our pickups. Constructed from Fibre board, and supplied with eyelets for easy soldering.

These focusing plates are mounted to the single coil and are generally used to make them sound warmer.

Please note, these are not official Fender® parts.